Building Supplies
Whether you need to replace parts on a damaged model, or build your own model rocket from scratch, Rocketry Works has the supplies you need.
- Body Tubes
- Display Stands
- Motor Tubes
- Tail Cones
- Transitions
- Couplers
- Bulkheads
- Centering Rings
- Nose Cones
- Recovery Gear
- Payloads
- Rail Buttons & Launch Lugs
- Motor Retention
- Fins
- Plywood and Balsa Sheets
- Tools
-
Replacement 3 Piece Nylon 1010 Rail Button Parts
Rocketry Works
$0.49These 3 piece replacement nylon replacement parts are handy in case you lose the plastic components to your 1010 rail buttons, or if you have a unique attachment requirement that does not require the standard 8-32 x 1/2 inch bolt and T-nut of Rocketry...RW-RB-1010-NYLON$0.49 -
Braided Kevlar Shock Cord by the foot
Rocketry Works
$0.11Braided Kevlar shock cord is incredibly strong for its weight and is heat resistant, so it makes a great shock cord in model rockets. Low power rockets can use 100 lb. tensile strength, while mid power rockets will do better with 250 to 750 lb tensile...RW-SC-BRAIDED-KEVLAR$0.11 -
3D Printed 1/4 inch Launch Lugs (1 pair)
Rocketry Works
$0.59These 3D printed 1/4 inch launch lugs feature Rocketry Works' unique mounting system that works with either wood glue or epoxy! These will stick well to a rough paper paper tube, so you may need to sand away any glossy finish on the tube at the...RW-LL-1-4$0.59 -
3D Printed Mid Power 1010 Launch Rail Guides (1 pair)
Rocketry Works
$0.99These 3D printed mid power rail guides feature Rocketry Works' unique mounting system that works with either wood glue or epoxy! These will stick well to a rough paper paper tube, so you may need to sand away any glossy finish on the tube at the...RW-RAIL-GUIDE$0.99 -
Sandpaper 8.5 x 11 sheet
Rocketry Works
$0.99Sandpaper in different grits is essential for preparing surfaces for adhesive, and for removing imperfections from finished surfaces. Available in a variety of grits: 80 grit for roughing wood, cardboard, plastic, or fiberglass surfaces for...RW-SANDPAPER$0.99 -
56mm (BT-70) Bulkhead
Rocketry Works
$1.99These laser cut bulkheads are made from 1/8 inch birch plywood, and sized to fit securely at one end of a 56mm (BT-70) coupler, and inside a BT-70 body tube. Sold as a set of 2 bulkhead plates, one smaller than the other. Each plate comes with 2...RW-BULKHEAD BT-70 PW 3MM$1.99 -
Custom Centering Rings (per ring)
Rocketry Works
$5.99We'll cut your custom plywood centering rings for you! Supported materials include 1/8 inch or 1/4 inch birch plywood. 1/8 inch ply is suitable for mid power applications where the difference in motor tube and airframe diameter is less than 3...RW-CR-CUSTOM$5.99 -
Replacement T-nut for 1010 Rail Buttons
Rocketry Works
$0.49Replacement T-nut for Rocketry Works' 1010 rail button. Includes one standard T-nut to fit Rocketry Works' 1010 rail buttons. Features a knurled threaded section for better grip when tightening against the inside of the airframe.RW-RB-1010-T-NUT$0.49 -
Replacement Hex Nut for 1010 Rail Buttons
Rocketry Works
$0.49Replacement hex nut for Rocketry Works' 1010 rail button. Includes one steel 8-32 hex nut to fit Rocketry Works' 1010 rail buttons.RW-RB-1010-HEX-NUT$0.49 -
Replacement Bolt for 1010 Rail Buttons
Rocketry Works
$0.99Replacement bolt for Rocketry Works' 1010 rail button. It is a stainless steel, 6-32 button head phillips bolt.RW-RB-1010-BOLT$0.99 -
Custom Length Tube
Rocketry Works
$3.99Rocketry Works can cut tubes for you to any length less than 34 inches, and we can optionally cut 3 or 4 1/8 inch slots in the airframe to your specifications.RW-TUBE-CUSTOM-CUT$3.99 -
Tail Cone for 29mm in BT-80
Rocketry Works
$5.99This ABS plastic tail cone includes an aft centering ring for a 29mm thin wall motor mount and 4 1/8 inch slots to allow through-the wall fins. Some sanding of the centering ring and the fin slots may be required. The 3D printed surface sticks CA glue,...$5.99